Beginner's Plumbing: What You Need for Installing a Bathtub
Beginner's Plumbing: What You Need for Installing a Bathtub
Blog Article
What are your ideas regarding A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't exactly rocket science, however it does require solid plumbing, carpentry, and occasionally, tiling skills. Changing an old bath tub with a new one is additionally a reasonably challenging project. If the old tub is conveniently easily accessible, the project can relocate speedily; if you need to open up a wall surface to get rid of the old tub and place the brand-new bathtub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and embeded in the brand-new one. See to it you have qualified yourself for the work and also are comfortable trying it. Rather than employing a professional to take over a halfway-completed job, it is much better to take into consideration utilizing one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This post will aid you set up a brand-new bath tub in your bathroom if you have actually currently bought a brand-new bathtub and don't need to transform the setup of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, activate the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather bothersome because of the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipes. Once the supply pipes have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the required setting. The wood boards are valuable in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bathtub until the level checks out degree.
To install taps, fit all-time low of the outermost versatile tap adapter to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the supply of water and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the bath tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling as well as securing around the bathtub must wait until the bathtub has been utilized at the very least when as this will settle it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type must be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface between the bath and also the tiling, leading to problems with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can split fairly early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that blog post about How to Install a Bathtub while browsing the web. If you enjoyed our blog posting plz be sure to pass it around. I enjoy reading our article about How to Install a Bathtub Yourself.
No more waits! Report this page